Gitae

Enhanced Gear Drives Research Group

Gitae home page > Publications > In proceedings of international conferences
In Proceedings of International Conferences
  • Lewicki, D. G., Woods, R. L., Litvin, F. L., Fuentes, A., "Evaluation of a Low-Noise, Formate Spiral Bevel Gear Set", Proceedings of 2007 ASME International Design Engineering Technical Conferences (IDETC) - 10th ASME International Power Transmission and Gearing Conference (PTG), Las Vegas, Nevada, USA, 4-7 septiembre, 2007.
  • Fuentes, A., Gonzalez-Perez, I., Litvin, F. L., Hayasaka, K., Yukishima, K., "Determination of Basic Machine-Tool Settings for Generation of Spiral Bevel Gears from Blank Data", Proceedings of 2007 ASME International Design Engineering Technical Conferences (IDETC) - 10th ASME International Power Transmission and Gearing Conference (PTG), Las Vegas, Nevada, USA, 4-7 septiembre, 2007.
  • Gonzalez-Perez, I., Fuentes, A., Litvin, F. L., Hayasaka, K., Yukishima, K., "Application and Investigation of Modified Helical Gears with Several Types of Geometry”, Proceedings of 2007 ASME International Design Engineering Technical Conferences (IDETC) - 10th ASME International Power Transmission and Gearing Conference (PTG), Las Vegas, Nevada, USA, 4-7 septiembre, 2007.
  • Gonzalez-Perez, I., Fuentes, A., Litvin, F. L., Hayasaka, K., Yukishima, K., "Computerized Design of Worm Gear Drives with Improved Conditions of Meshing and Bearing Contact", Proceedings of 2006 ASME International Mechanical Engineering Congress and Exposition, Chicago, Illinois, USA, 5-10 noviembre, 2006.
  • Fuentes, A., Gonzalez-Perez, I., Litvin, F. L., Hayasaka, K., Yukishima, K., "Design, Manufacture, and Evaluation of Prototypes of Low-Noise High-Endurance Spiral Bevel Gear Drives", Proceedings of IDETC 2005 ASME International Design Engineering Technical Conferences, Long Beach, California, USA, Septiembre, 2005.
  • Gonzalez-Perez, I., Fuentes, A., Litvin, F. L., Hayasaka, K., Yukishima, K., "Modified Surface Topology of Involute Helical Gears Developed for Improvement of Bearing Contact and Reduction of Transmission Errors", Proceedings of IDETC 2005 ASME International Design Engineering Technical Conferences, Long Beach, California, USA, Septiembre, 2005.
  • Gonzalez-Perez, I., Fuentes, A., Litvin, F. L., Hayasaka, K., Yukishima, K., "New Topology of Helical Gear Drives with Modified Motion Graph", Proceedings of the International Conference on Gears, VDI-Berichte 1904, Vol. 1, pp. 721-735, Munich, Septiembre, 2005.
  • Fuentes, A., Litvin, F. L., Mullins, B. R., Woods, R., Handschuh, R. F., Lewicki, D., "Design, Stress Analysis and Experimental Test of Low-Noise Adjusted Bearing Contact Spiral Bevel Gears”, Proceedings of the International Conference on Gears, VDI-Berichte 1665, Vol. 1, pp. 327-340, Munich, Marzo, 2002.
  • Pedrero, J. I., Artés, M., Pleglezuelos, M, García-Masiá, C.; Fuentes, A., "Theoretical model for load distribution on cylindrical gears: application to contact stress analysis", AGMA 1999 Fall Technical Meeting, Paper 99FTM15, October 1999.
  • Pedrero, J.I., Estrems, M., Fuentes, A., "Determination of the Efficiency of Cylindrical Gear Sets", Proceedings of the IV World Congress on Gearing and Power Transmissions, Paris (France), Vol.1, pp. 297-302, June 1999.
  • García-Masiá, C., Fuentes, A., Ruipérez, A., "Computer Modelling of 3D Basic Rack Generated Bevel Gears", Proceeding of the IV World Congress on Gearing and Power Transmissions, Paris (France), Vol. 1, pp. 667-675, June 1999.
  • Pedrero, J.I., García-Masiá, C., Fuentes, A., "On the Location of the Tooth Critical Section for the Determination of the AGMA J-Factor", AGMA 1997 Fall Technical Meeting, Paper 97FTM6, San Diego, California, 1997.
  • Estrems, M., Fuentes, A., Pedrero, J.I., "Influencia de los Parámetros Geométricos y de funcionamiento en el Régimen de Lubricación de Engranajes Cilíndricos”, Anales del III Congreso Iberoamericano de Ingeniería Mecánica, Cuba, September 1997.
  • Pedrero, J.I., Solano, J., Fuentes, A., García-Masiá, C., "Sistema de CAD para Optimización de Reductoras en Dos Etapas", Anales del II Congreso Iberoamericano de Ingeniería Mecánica, Brasil, December 1995.
  • Pedrero, J.I., García-Masiá, C., Fuentes, A., "Optimization of Gear Design by Parametric Analysis", Proceedings of the Gear Transmissions’95 – International Congress, Sofía (Bulgaria), September 1995.
  • Pedrero, J.I., García-Masiá, C., Fuentes, A., "Theoretical Approach to Wear Stress Calculation for Involute Gear Teeth", Proceedings of the Ninth World Congress on the Theory of Machines and Mechanisms, Milán (Italia), Septiembre 1995.